Dior Maison reveals - for the first time - a new wallpaper adorned with Toile de Jouy. Dior Maison reimagines the signature motif as a non-woven wallpaper, reflecting an exceptional French savoir-faire. Its traditional fiber texture offers a unique effect, similar to linen. The exclusive and recyclable material revisits the emblematic drawings in a variation portraying wild animals, offered in delicate ivory-gray tones. A new invitation to enchant your interior with the House’s timeless codes.
Recyclable and non-woven high-end wallpaper
PVC base wall covering on paper support
Ink with no solvents
Weight: 300 Gr (10.5 oz)
Moderate scratch and impact-resistant surface
Washable
Quick drying time
M1 fire rating
Doesn’t leave any residue upon removal
Simple application
Quick and careful shipment in rigid packaging
Dimensions: 62 x 6.5 cm / 24.5 x 2.5 inches (rolled) and 62 x 300 cm / 24.5 x 118 inches (laid flat)
Made in France
Application of wallpapers and wall coverings
Material:
- Plumb line or level
- Pencil
- Glue for non-woven wallpaper
- Smoothing brush
- Wallpaper roller
- Utility knife
- Ruler
Before starting:
Make sure the wall is smooth, clean and dry. If there are any bumps, remove them with the appropriate sandpaper. Remove the switch and plug covers.
Put them back in place after the installation. To place the first panel as straight as possible, use a level or a plumb line. Trace a straight line 62 cm (24.5) from the wall edge, which you will use as a point of reference for the first panel.
Glue:
Our wallpapers are non-woven and there is a specific glue for this type of material. We recommend you use one labeled 'without solvents'. Prepare the glue as indicated on the product instructions. Directly spread the glue on the wall with a roller or a glue brush.
The application:
Unroll the roll and start from the top of the wall. If the wall isn’t straight, start from the highest side or have your wallpaper exceed the wall by 2 - 3 cm (1). Smooth the wallpaper with a special brush starting from the interior towards the exterior to remove air bubbles. Cut off the surplus at the baseboard and ceiling, using a utility knife and ruler. Use the wallpaper roller on the edge of the panels to prevent them from lifting up.
Material:
- Plumb line or level
- Pencil
- Glue for non-woven wallpaper
- Smoothing brush
- Wallpaper roller
- Utility knife
- Ruler
Before starting:
Make sure the wall is smooth, clean and dry. If there are any bumps, remove them with the appropriate sandpaper. Remove the switch and plug covers.
Put them back in place after the installation. To place the first panel as straight as possible, use a level or a plumb line. Trace a straight line 62 cm (24.5) from the wall edge, which you will use as a point of reference for the first panel.
Glue:
Our wallpapers are non-woven and there is a specific glue for this type of material. We recommend you use one labeled 'without solvents'. Prepare the glue as indicated on the product instructions. Directly spread the glue on the wall with a roller or a glue brush.
The application:
Unroll the roll and start from the top of the wall. If the wall isn’t straight, start from the highest side or have your wallpaper exceed the wall by 2 - 3 cm (1). Smooth the wallpaper with a special brush starting from the interior towards the exterior to remove air bubbles. Cut off the surplus at the baseboard and ceiling, using a utility knife and ruler. Use the wallpaper roller on the edge of the panels to prevent them from lifting up.
因技术局限、产品改良或生产批次等原因，网站中的信息可能存在色差、尺码误差、成分含量误差或其他细节误差，网站展示的产品图片可能与产品实际外观不一致，以产品实物为准。如有相关问题，请致电迪奥客服中心。
